DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Plain Blue Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 48” and 52” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Doughboy, Vouge, Teakwood Discovery, Equinox , Regatta & Regatta II, Topaz, Reprieve, Oracle, Trevi 205, Summer Days.

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Plain Blue Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 36” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Splasher

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Replacement Doughboy Liners for both the Regent and Premier. High quality liners with unbeatable warranty on the seam. In stock for quick delivery

Doughboy Replacement Liners are all plain blue overlapping liners which are stretched into place, this can be a difficult task to do so please follow the instructions below.

1. Check and Double Check: It’s is vital to check that all levels and measurements are correct before positioning your Doughboy Liner. The cove is a vital structural element that prevents water pressure from forcing the liner out under the bottom rail. So please be sure that cove is installed correctly by manufactures guidelines.
2. Seam Positioning: Check the pool floor (area inside the walls) for levelness. Fill in all depressions and remove any stones or sharp object from floor. Place the Doughboy liner on the top of top rail, the liner should have overhanging the outside wall by 12” inches. Hold end and unroll liner down middle of pool as you would carpet, do not place liner seam over skimmer or return fitting openings.
3. Install Liner: Work in both directions from the point where is already overhanging, unfold Doughboy liner, drape over the top rail and down the sides approximately 24” inches. The liner should be barely above the pool floor in the centre only. Remember that the centre seam or centre of the Doughboy Plain Blue liner should be inside the pool about 12” inches below the top rail. Correct any bunching or pleating conditions in the liner wall. Inspect the liner for open seams if any found return to dealer for prompt replacement of liner.
4. Fill Pool: With the Doughboy Plain Blue liner in position, hold in place by attaching heavy duty clips over folded cardboard on the underside of each top rail. Carefully cover the end of the garden hose with a sock and tape securely, once this is done place hose inside the pool and start filling. As pool fills the liner will stretch as the water begins to cover the bottom. At this point check the walls for EXTREME tautness, release clips if need be but be sure not to release too much slack as this will cause creases. When releasing the clips you will also need to keep in mind the clips will need to be loosened evenly for whole circumference of the pool (Doughboy advise very little amounts at a time). Once the water reaches past the cove the tension should ease off dramatically and you should have no wrinkles on the floor. Creases in the wall can be removed by re-tauting the Doughboy Plain Blue liner over the wall,
5. Procedure to attached liner: With the help of two or three people, raise and hold the Doughboy Plain Blue liner up from any three top rail sections. Remove some of the top rail completely and stretch the Doughboy liner over metal wall as tight as possible, then re-erect the top rail with the liner in position and repeat the procedure all the way round the pool (Remembering only taking 2-3 sections off at one time) Once this is completed and the water is at correct level then the water can be turned off and cuts to the liner can be made.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Plain Blue 30 Thou Swimming Pool Liner is an ideal replacement for any tired or damaged swimming pool liner. Made in the UK by the country's largest pool liner manufacturer the Plain Blue 30 Thou Pool Liners are of the highest quality and each one has its own individual code for ease of re-ordering.

We have provide a list of prices as a guide. The liners are priced for Rectangular hopper or wedge pools with a shallow end wall height of 3ft 4". If you pool is of a different wall height please contact us for a very competitive quote.

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. 

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

Start at the Deep End and secure the liner bead into the linerlock. Work your way round the pool, if two people go in opposite directions. 

Once the liner is fully fitted into the liner lock check how the liner is hanging and adjust where needed. at this stage if possible "Set" your liner with a pool liner vacuum. This will pull the liner against the pool walls and floor, ensuring there are no creases when filling. At this stage fit main drain.

Once any wrinkles are removed start filling the pool. As the pool water rises fit the returns and skimmers as the the water reaches just below each fitting. This will allow the liner to have fully stretched in and reduce any risks of leaks.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

Prices below are are for Rectangular hopper or wedge pools with a shallow end wall height of 3ft 4". If your pool has a deeper shallow end please contact us for a very competitive quotation.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Plain Blue 20 Thou Swimming Pool Liner is an ideal replacement for any tired or damaged swimming pool liner. Made in the UK by the country's largest pool liner manufacturer the Plain Blue 20 Thou Pool Liners are of the highest quality and each one has its own individual code for ease of re-ordering.

We have provide a list of prices as a guide. The liners are priced for Rectangular hopper or wedge pools with a shallow end wall height of 3ft 4". If you pool is of a different wall height please contact us for a very competitive quote.

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. 

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

Start at the Deep End and secure the liner bead into the linerlock. Work your way round the pool, if two people go in opposite directions. 

Once the liner is fully fitted into the liner lock check how the liner is hanging and adjust where needed. at this stage if possible "Set" your liner with a pool liner vacuum. This will pull the liner against the pool walls and floor, ensuring there are no creases when filling. At this stage fit main drain.

Once any wrinkles are removed start filling the pool. As the pool water rises fit the returns and skimmers as the the water reaches just below each fitting. This will allow the liner to have fully stretched in and reduce any risks of leaks.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

Prices below are are for Rectangular hopper or wedge pools with a shallow end wall height of 3ft 4". If your pool has a deeper shallow end please contact us for a very competitive quotation.