DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post. A Returns Number must be obtained before sending goods back.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors..

PRODUCT INFO:

Solar Pods & Solar Pod Plus are an ideal solar heating solution for your above or in-ground swimming pool. Solar heating using a Solar Pod is one of the most cost effective methods of heating your pool. Once you have purchased this Solar Heating System every Kilowatt of heat produced for your water is totally free. Whether you use the Solar Pods as a top up for your existing pool heater or as the only form of Heating it makes economical & environmental sense to use for your Swimming Pool. The Solar Pod Plus are an extra large, stronger and more robust system for increased performance. Please see the specification chart to calculate how many you will need for your swimming pool.

 

The Solar Pod Plus are 31" (780mm) square, but due to the design offer more than twice the heating capabilities of a standard solar pod. The Solar Pod Plus also has a reflective base to increase heat gain to the absolute maximum. Installing the desired number of Solar Pod Plus into a small space is very achievable. Each Solar Pod Plus has two tilting legs to help achieve the perfect angle to the Sun. Solar Pods, as with any swimming pool solar collector heating system, should be faced due South.

Each Solar Pod Plus Kit Contains:

    Main Solar Pod Plus Base & Stand

    Reflective Underside For Optimum Heat Gain

    1.25" to 1.5" Hose Reducer

    Collared Tube Adapters & Gaskets (For Larger Intex Pools)

    Hose Clamps

    1 x 1m Hose & 1 x 380mm Hose

    Side Hose Connectors

    Clear Dome

    Solar Protection Cover

Solar Pod, Solar Pods Plus and Athena Sun Domes have become one of the most popular heating systems for swimming pool over the past few years as they are a quick, inexpensive and effective method for heating of your water. Each Solar Pod measures 580mm sq, Solar Pod Plus measure 780mm sq, both are easy to connect to any  filtration system.

Solar Pod Plus are capable of heating 9,000 litres of water and are designed to perform to a higher standard than the Solar Pods which are capable of heating 4,500 litres of water. Solar Pod Plus are larger in size, are double skinned and contain far more internal coil to produce more heat for your Swimming Pool. We also stock Athena Sum Domes which are a very similar, but more efficient product that can heat 7,500 litres per dome.

This Solar Heating System is suitable for all styles of pools, from the summer fun Intex style pools up to Inground tiled pools. Every Pod connects to each other in a series offering the most effective Solar Heating style. Use our sizing chart on the Specification page to decide how many you will need for your swimming pool.

 Specification:

• Suitable for above ground and in-ground swimming pools
• each Solar Pod is 580mm x 580mm Solar Pod Plus are 780mm x 780mm
• Coil made of strong polypropylene
• Solar Pod Dome made of strong transparent polycarbonate ( Greenhouse Effect )
• Easy Connections
• Connect multiple units for larger swimming pools
• Solar Pods Works with existing pool pumps
• Minimal tools required (Philips screwdriver and silicon lubricant)
• Solar Pods Tilt to give you more direct sunlight
• No servicing required (only when closing your pool)
• Silver base on Solar Pod Plus to generate more heat

As with all swimming pool solar heaters, sizing is an estimation and can alter depending on local climate and strength of sun.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days.

RETURNS: All products can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Solar Cover Reel Roller System Especially Designed For Intex, Bextway & Other Above Ground Soft Sided Metal Frame Pools.

Solaris reel for above ground pools - Fitting a solar cover reel roller system on an Intex Rectangular Pool has not been an easy task in the past. Well now fitting a solar cover reel roller to an Intex Metal Frame Pool can not be easier.

The Solaris Solar Cover Reel Roller System is large enough for Intex, Bestway & similar pools 20ft Diameter. Although this reel system can accomidate fit on large pools it will not work if you use heavier 500 micron covers. If you are unsure please call to discuss

The Solaris Intex, Bestway Solar Cover Reel Roller System comes complete with straps to attach to your solar cover.

DELIVERY: Made To Order - 7 - 10 working days delivery

RETURNS: This product is Made To Order and as such is classed a s a special order which cannot be returned unless with a manufacturing defect. Returns should be sent via a "Signed For" carrier or post. A Returns Number must be obtained before sending goods back.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors..

PRODUCT INFO:

Solar Weave Swimming Pool Heat Retention Bubble Cover is manufactured for use in frequently used pools where durability is essential. Made from a 400 micron Solar Bubble with a tough, tear resistant woven surface the SolarWeave Heat Retention Cover is particularly suitable for outdoor Commercial or Semi-Commercial pools where the need for heat retention is high, but allowing the benefit of Solar heat gain that other heat retention covers cannot supply. 

The Solar Weave Swimming Pool Heat Retention Cover can be used all the the time the pool is open. If your pool is open 12 months of the year and you require a heat retention cover that will work for you all year round then the Solar Weave cover is for you.

These covers are made to order so lead times are between 7 - 10 days. 

We have shown example prices for standard sized pools but these covers can be made for any size or shape of pool. Please call or Contact Us for a quote

Solar Weave Heat Retention Bubble Cover Specification

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

The spa pillow from life is the perfect relaxation acceessary for any hot tub or spa. The pillow is made of high quality suede material and has duel suction points to hold it in place.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

A comfortable and attractive design that is made of  heavy duty heat resistent material. The booster seat is held in position by strong suction cups to prvent the seat from floating or moving.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: Spa Tiger can be returned unused, in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

What to expect after installing the Spa Tiger

The following is offered as a guide:

Hot Tub Water becomes crystal clear

Heavy metal particles removed

A low, gradually stabilizing pH level

Cyanuric acid level begins to gradually decrease

Percentage of free available chlorine gradually increases

Existing scale begins to disappear 

HOW DOES THE SPA TIGER WORK

The Spa Tiger was designed to harness an all-natural process known as Hydrodynamic Cavitation. In our device this process relies solely on the flow of water as driven by your Hot Tub's Pump. 

Constructed of hardy thermoplastic, the Spa Tiger has no moving parts. It does not require electricity nor does it contain any cartridges or other components that will ever require replacement. 

HYDRODYNAMIC CAVITATION

The effects of cavitation have been known for more than a hundred years, but only recently has this phenomenon been harnessed to provide several important benefits.

Cavitation in our device occurs when water accelerates within the device’s nozzle. This acceleration drops the pressure of the water below the vapor point, resulting in the formation of small vapor bubbles. As the vapor bubbles exit the nozzle, the pressure of the surrounding water causes them to rapidly collapse and revert to a liquid state once again.

This rapid change in water’s states of matter creates:
- High levels of infrared energy (heat )
- Intensive shock waves

These factors are sufficient to:
- Oxidize and destroy exposed contaminants – this improves sanitation and reduces the need for chemical treatment
- Initiate the gradual decomposition of acids – this raises pH and eliminates excessive levels of cyanuric
- Change the polarity of suspended particles, causing them to agglomerate to a size at which they are easily captured by the filter – this clarifies water and creates a more inviting swimming environment
- Affect the bonds between the hydrogen and oxygen atoms which constitute water molecules - this produces a phenomenon known as "structured water"

It is important to note that the heat produced by cavitation is quickly absorbed by the surrounding water. As such, it does not raise the temperature in the Hot Tub by any measurable degree.

STRUCTURED WATER

Most of the water on our planet is composed of small groups of water molecules randomly joined together by means of shared hydrogen atoms. These molecular groups are irregular in size and shape.

Under certain conditions, however, water molecules can join together in precisely configured groups consisting of sheets of hexagonal cells. Due to their well-defined structure these molecular groups are called “structured water.”

In extremely cold conditions the sheets of hexagonal cells are linked together by connecting protons, which confers solidity. Structured water formed under these conditions is known as ice.

In extremely warm conditions the sheets of hexagonal cells lack the connecting protons and thus they retain the property of liquidity.

In our device the extreme heat and intensive shock waves resulting from cavitation cause the hydrogen and oxygen atoms in affected water molecules to temporarily disassociate and then re-associate as the water cools. As they re-associate, they do so in sheets of hexagonal-shaped cells.

Whether solid or liquid, structured water is said to be exclusionary because it tends to reject any material that is not structured water. This is why icebergs, which are formed from salt water in the oceans, contain no salt.

In liquid form, structured water tends to collect at hydrophilic surfaces, such as Hot Tub surfaces, pipes, equipment and even the surface of the water itself. There it will reject any material that is not structured water.

The Spa Tiger is very easy to install. It ships fully assembled with unions and requires no electricity. Unless a loop is required due to space considerations on existing equipment sets, an experienced installer should be able to complete the installation within 15 minutes.

IMPORTANT: Spa Tiger will not work if not installed in the incorrect direction. 

The Spa Tiger does not need a separate electrical supply, but operates on the flow of water as driven by the Spa's pump. It activates at a minimum flow rate of 1.8m3 per hour. In essence, the device converts the energy provided by the pump into a variety of benefits. 

The more the pump runs, the more Spa Tiger is doing to sanitize, clarify and enhance water quality as well as protecting pool surfaces from buildup and staining. 

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Sylvania LED Spare Parts refurbishing Existing Certikin PU9 or PU6

Spare parts for Sylvania Swimming Pool Lights, Swap to LED, same money on electric costs, have a brigher light and amazing options to change the colour of the lights. The Sylvania LED underwater swimming pool lights are a professional light system for underwater illumination of your swimming pool.

One Transformer PU11H is suitable for upto 3 LED Sylvania Lights

Deck for listed is in white but other colours are available - blue and graphite

The Sylvania Colour change lights combine high power LED's of red, green, blue and fixed white colours together with an internal microprocessor, it is capable of generating the full spectrum of colours.

Remote control unit and receiver unit are available - The lamp can be operated in a mode of continuous colour changing or fixed at any desired colour by briefly switching the lamp off and back on again.

 

 

 

PRODUCT INFO:

The Speck EasyFit Pump is the champion of flexibility with seven connection sets, making the EasyFit pump compatible with at least six different pump types.

Free Connection to replace the following pumps for easy retro fit - just tell us what pump you have from the below

Pentair UltraFlow, Pentair WhisperFlo, Hayward Super Pump, Sta-Rite 5P2R, Astral Super Sprint, Astral Victoria Plus, Wilo Filtec FBS, Sta-Rite 5MPR Dyna Glas, Hayward RSII

The often time-consuming task of installing a new circulation pump into an existing filter unit is a thing of the past.

The pump can be installed maximum 3 m above or below water level.
The bellows-type mechanical seal is mounted on a plastic shaft protector sleeve.

Motor/pump shaft has no contact with the pool water, providing complete electrical separation.

Easy connection to existing pipes – height adjustable pump feet reduce assembly time and effort.

Metric and imperial unions supplied – see table below for sizes.

PRODUCT INFO:T

The Speck EasyFit Pump is the champion of flexibility with seven connection sets, making the EasyFit pump compatible with at least six different pump types.

Free Connection to replace the following pumps for easy retro fit - just tell us what pump you have from the below

Pentair UltraFlow, Pentair WhisperFlo, Hayward Super Pump, Sta-Rite 5P2R, Astral Super Sprint, Astral Victoria Plus, Wilo Filtec FBS, Sta-Rite 5MPR Dyna Glas, Hayward RSII

The often time-consuming task of installing a new circulation pump into an existing filter unit is a thing of the past.

The pump can be installed maximum 3 m above or below water level.
The bellows-type mechanical seal is mounted on a plastic shaft protector sleeve.

Motor/pump shaft has no contact with the pool water, providing complete electrical separation.

Easy connection to existing pipes – height adjustable pump feet reduce assembly time and effort.

Metric and imperial unions supplied – see table below for sizes.

PRODUCT INFO:

The Speck EasyFit Pump is the champion of flexibility with seven connection sets, making the EasyFit pump compatible with at least six different pump types.

Free Connection to replace the following pumps for easy retro fit - just tell us what pump you have from the below

Pentair UltraFlow, Pentair WhisperFlo, Hayward Super Pump, Sta-Rite 5P2R, Astral Super Sprint, Astral Victoria Plus, Wilo Filtec FBS, Sta-Rite 5MPR Dyna Glas, Hayward RSII

The often time-consuming task of installing a new circulation pump into an existing filter unit is a thing of the past.

The pump can be installed maximum 3 m above or below water level.
The bellows-type mechanical seal is mounted on a plastic shaft protector sleeve.

Motor/pump shaft has no contact with the pool water, providing complete electrical separation.

Easy connection to existing pipes – height adjustable pump feet reduce assembly time and effort.

Metric and imperial unions supplied – see table below for sizes.

DELIVERY: Spectrum Hybrid UV Systems are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.

RETURNS: Spectrum UV Systems can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.

.

When a return is received back into our warehouse our returns department confirm that everything is present and that the item is in its original condition, to make sure it is eligible for a refund. We will process the refund normally on the same day we take them in, but please allow up to a maximum of 14 working days for the money to reach your bank or credit card. It is unlikely to take this long but due to reasons such as bank delays or errors, this may occasionally occur.

PRODUCT INFO:

Elecro's Spectrum Hybrid is the next generation of UV water treatment. Providing a safe environment in clear water, the Spectrum Hybrid kills micro-organisms such as bacteria, viruses, chloramines and pathogens found in water, costing no more than a common light bulb to run. The next step in UV treatment, the unit creates Hydroxyl Radicals, which are essentially a water molecule with a Hydrogen atom removed, causing the molecule to be highly volatile and reactive. The exceptional mobility of the molecules that fill the reaction chamber leads to the destruction of pollutants in their path. Once the Hydroxyl  Radical has reacted with the pollutant it converts back into water.

Built to be installed easily into your existing set-up, all Spectrum Hybrid units are supplied complete with flow switch and the choice of either a lamp life indictor (which flashes ‘Red’ when the UV lamps are required to be changed after 9,000 hours) and reset switch; or a digital lamp life countdown and intelligent peristaltic dosing pump.

• Activated titanium reaction chamber produces Hydroxyl Radical oxidisers, and increases the sterilising effiency by up to 45% compared to traditional UV’s
• Two Power Options:
  • 55 Watts for flow rates up to 12m³/hour (50m³ pool volume)
  • 110 Watts for flow rates up to 24m³/hour (100m³ pool volume)
• Destroys micro-organisms such as bacteria, viruses, chloramines and pathogens, and provides a safe swimming environment in clear water
• Costs no more to run than a common light bulb
• Salt and sea water compatible
• Reduces chemical requirement
• 3-year warranty
• All Spectrum Hybrid units are supplied complete with flow switch and the choice of:
  a) 9,000 hour lamp life indicator and reset switch or
  b) Digital lamp life countdown and Intelligent dosing pump

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Plain Blue Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 36” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Splasher

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Swimming Pool Foam Underlay & Wall Insulation Adhesive is designed to quickly bond the foam into place on swimming pool walls and floors.

It is not a "Quick Grab" adhesive so you do have time to position the foam underlay correctly before it sets.

Available in single cans or boxes of 12.

We would advise 5 cans per 50m2 of Foam Underlay

The chart below will help you estimate the number required

Standard Hopper Pool	Floor  Area m2	Wall Area m2
10' x 20'	24.2	18.6
12' x 24'	34.8	22.3
14' x 28'	47.3	26.0
14' x 30'	50.7	27.2
15' x 30'	54.3	27.9
16' x 32'	61.8	29.7
16' x 38'	73.4	33.4
18' x 36'	78.3	33.4
20' x 40'	96.6	37.2

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors.

PRODUCT INFO:

The Sta-Rite 5P2R is the pump most fitted on domestic swimming pools in the UK. Price, reliabilty and quiet running make it THE choice for domestic swimming pools. 3 Year Warranty

Sta-Rite 5P2R swimming pool pump is precision molded of fiberglass reinforced, temperature and corrosion-resistant. This lightweight exceptionally strong thermoplastic is designed for much higher pressure operation than other pool pumps. Unequaled performance means: higher heads to 22, 5 meters and flow rates up to 22m3/h.

The S5P2R series are suitable for water with a salt content up to 0,4% and for water with pH fluctuations (corrosion). The capacity and dimensions are identical to the series 5P2R. Special motor shaft and all inner parts are made from high grade stainless steel or thermoplastic material.

HIGH HEAD IMPELLER - Precision molded of glass filled polycarbonate, it provides unusually smooth water passages for outstanding performance and efficiency

HEAVY DUTY MOTOR - 50 Hz motors are designed for continuous andquiet operation, feature stainless steel shaft, sealed and permanently lubricated bearings: runs cooler for prolonged life under high ambient conditions.

MECHANICAL SEAL - Precision lapped and highly polished carbon ceramic stainless steel construction, it assures maximum drip proof corrosion free protection

STAINLESS STEEL PUMP CHAMP - Easily removed for quick access to all serviceable components

SEE THRU’ TRAP LID - Designed to withstand 4 bar test pressure as well as high vacuum conditions

3 YEAR WARRANTY

 

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors.

PRODUCT INFO:

The Sta-Rite Dyna-Glas 5P6R is a self priming rapid swimming pool pump, designed for medium to large swimming pools or any other aquaculture applications. The Sta-Rite 5P6R is the best pump around if you require a very high flow rate and where extra quiet operation is required or preferred.

The Sta-Rite 5P6R is manufactured in Europe, not China like so many pumps and is built to perform for many of years, the motor is built in accordance to the European CE-Standards with IPX5 protection. As standard the Sta-Rite 5P6R comes complete with a high quality glass reinforced thermoplastic construction which is extremely high corrosion free, also included is a cool running shaft which provides a longer life and better wear preventing seal damage from loss of prime.

The Sta-Rite 5P6R is a fast self-priming pump with medium head, sizes available are from 0.75HP through to 3HP with an extra-large integral hair and lint strainer, which can strain out the smaller particles which most pump are unable to. It is easy to service and maintain with an extra-large internal trap.

This pump can self-prime up to 5m above water level giving it a huge advantage for being used away from the Swimming Pool and at higher levels.

DELIVERY: In-stock items are sent out on a next working day service

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post. A Returns Number must be obtained before sending goods back.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors..

PRODUCT INFO:

Pentair Superflo Pumps have been replaced with the Supermax S5P1R. The S5P1R pumps are specifically designed to be the best choice for a variety of inground swimming pools. Same features as the superflo with thick walled body parts and a heavy duty 56 square flange motor and a highly engineered hydraulics.

The Pentair Superflo Pump now replaced by the S5P1R one of the world’s most popular swimming pool pumps offering the highest quality at a very affordable price. 

The Pentair S5P1R Swimming Pool Pump has a whisper quiet operation due to the internal hydraulic design and the hardwearing, thick walled body is designed for exceptionally heavy usage. The Pentair Superflo Pool Pump is an ideal replacement pump for all inground swimming pools that need a quiet, hard working pump that does not cost the earth. If your swimming pool currently has a Hayward Super Pump fitted the Pentair Superflo  / S5P1R will directly replace it without having to alter any pipework.

The Pentair Pump has a simple Cam & Ramp, quarter-turn, super-sized locking lid. Offering a large easy to remove strainer basket with a lid that needs no tools or poles to open makes the Pentair Superflo a pleasure to own.

S5P1R meets all the criteria for a superior pool, spa or water feature thanks to its PENTEK motor. It's super energy efficient. It's quiet and super easy to maintain. Furthermore, it's designed with innovative materials that will stand up to demanding installation and conditions. Whether you're choosing your first pump or replacing older technology, Superflo is definitely a Super choice.

The Pentair S5P1R in 0.5hp up to 3hp

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Strap Set for Swimming Pool Reel Systems(10 pack)

Pack contains: 10 Straps, 10 Poppers, 10 Adjustment Clips & 10 Screws 

 In this Strap Set kit there will be everything you require to be able to attach your Solar Cover to your Reel system.

Keeping the right distance on your straps is important in being able to being able to roll your Solar Cover up evenly. Measuring and marking where your straps would attach before fitting them allows you to understand if your straps are evenly distributed.

 

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Strap Set for Swimming Pool Reel Systems (10 pack)

The Unviversal Strap Set comes in a pack of Ten straps which can be used to connect your Swimming Pool Solar Cover to your Reel System. This Strap Set is a easy DIY pack that will provide everything you need to attach your cover to your reel.

The Unviversal Strap Set comes in a pack of 10 which can be used to connect your Reel system to your Swimming Pool Solar Cover. In this Strap Set kit there will be everything you require to be able to attach your Solar Cover to your Reel system. You will follow a easy process that will keep your Solar Cover tight to your reel when being rolled up.

Keeping the right distance on your straps is a major key in being able to being able to roll your Solar Cover up evenally. So when placing your poppers on to your Solar Cover it is a good idea on using the same length on from the edge of your cover to help you out from the start. Measuring and marking where your straps would attach before actually fitting any is a perfect way of knowing its evenally marked out before you start fitting them.

DELIVERY: Sun Spring Heat Pumps are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.

RETURNS: Sun Spring Above Ground Pool Heat Pumps can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.

When a return is received back into our warehouse our returns department confirm that everything is present and that the item is in its original condition, to make sure it is eligible for a refund. We will process the refund normally on the same day we take them in, but please allow up to a maximum of 14 working days for the money to reach your bank or credit card. It is unlikely to take this long but due to reasons such as bank delays or errors, this may occasionally occur.

PRODUCT INFO:

The Sunspring Plug & Play Swimming Pool Heat Pumps are made especially above ground pools. These heat pumps, up to the 9kw, do not have to be hard-wired in, saving up to £500 on installation costs. As the 5, 8 & 12 Sun Spring Plug & Play Swimming Pool Heat Pump will plug into a 13 amp socket and does not require a by-pass, installation can be carried out in as little as 15 minutes by anyone. 

We have other ranges of Plug & Play Swimming Pool Heat Pumps available, which are less expensive than the Sunspring Heat Pump, but just as well made and all with 2 Year Warranties.

Poolstyle Mini 6 & 8 Plug & Play Above Ground Pool Heat Pump - Click Here

Flotide A10 9.6kw Plug & Play Swimming Pool Heat Pump - Click Here

To get the best from your Sunspring Heat Pump it is advisable to size the heat pump to the middle of its capabilities. To assist you in choosing the most suited Sunspring Heat Pump for your pool we have provided a guide of MAXIMUM POOL SIZES. If the volume of water in your pool is equal to or larger than the maximum volume it is always advisable to go for the next larger heat pump, as it will be easier to maintain your pool water temperature and potentially provide extended use outside the main 3 summer months.

Sunspring Heat Pumps Will Be Despatched Same Day If Ordered By 11 AM

For advice and help on choosing the Sunspring Heat Pump suitable for your pool please call us on 01322554870

Maximum Pool Size

Sunspring 5 Above Ground Pool Heat Pump  pools up to 12m3 - 15ft x 36" Metal Frame Pool

Sunspring 8 Above Ground Pool Heat Pump  pools up to 20m3 - 15ft x 48" Metal Frame Pool

Sunspring 12 Above Ground Pool Heat Pump  pools up to 30m3 - 18ft x 48" Metal Frame Pool

Minimum Flow rate required  

3m3/hr on Sunspring 5

4m3/hr on Sunspring 8

5m3/hr on Sunspring 12

Sunspring Heat Pumps come with graduated hose-tails to connect to 1.25" & 1.5" flexible hose. Also included are Glue Sockets for 50mm or 1.5" rigid pipe. In addition, no bypass kit is necessary.

The Sun Spring Heatpumps have a 2 Year Collect & Repair Or Replace Warranty. 

If you require help in sizing your heat pump or have any questions, please call us on 01322 55 4870

 

DELIVERY: We aim to send Superpool Side Mount Sand Filter For Swimming Pools out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This Superpool Side Mount Sand Filter For Swimming Pools can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Superpool Side Mount Sand Filters Are An Ideal Replacement for Lacron Sand Filters & Tagelus Sand Filters. 

Superpool side mounted filter are made from extremely robust and hard wearing fibreglass tank with a smooth Gel coat. These filters are ideal for medium to large sized pools and come complete with a large 9.5" clear lid for easy sight view of the inflow diffuser along with a helpful removal tool. The tank alone comes with a 10 years warranty. 5 years longer than the Tagelus or Lacron. 

Superpool Side Mount Filter 20" requires 100kg media - pools up to 65 cubic metres

Superpool Side Mount Filter 26" requires 150kg media - pools up to 85 cubic metres

Superpool Side Mount Filter 30" requires 250kg media - pools up to 100 cubic metres

Superpool Side Mount Filter 36" requires 375kg media - pools up to 130 cubic metres

Product Code	Model & Tank Diameter	Connections	Max Flow Rate	Sand (kg)
88014004	SMG500 - 20" - 516mm	1.5"	10m3/h	100
88014005	SMG650 - 26" - 667mm	1.5"	16.5m3/h	150
88014063	SMG750 - 30" - 770mm	2"	22.1m3/h	250
88014064	SMG900 - 36" - 920mm	2"	32m3/h	375

DELIVERY: We aim to send Superpool Side mount Sand Filters out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This Superpool Side Mount Sand Filter can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Superpool Side Mount Sand Filter For Domestic Swimming Pools have a smooth finish Gel Coat Fibreglass body and are perfect replacements for old Tagelus or Lacron Side Mount Swimming Pool sand Filters

A 9.5" Transparent Lid with "easy Remove" tool along with the high quality side mount multiport valve (MPV) allow for easy operation and  long lifespan.

Superpool Side mount sand filters are designed to operate at flow rates between 10m3 to 32m3 depending on filter size.

Superpool Side Mount Filter 20" requires 100kg media - pools up to 65 cubic metres

Superpool Side Mount Filter 26" requires 150kg media - pools up to 85 cubic metres

Superpool Side Mount Filter 30" requires 250kg media - pools up to 100 cubic metres

Superpool Side Mount Filter 36" requires 375kg media - pools up to 130 cubic metres

Model & Tank Size	Product Code	Connections	Max Flow Rate	Sand (kg)
SMG500 - 20" - 516mm	88014004	1.5"	10m3/hr	100
SMG650 - 26" - 667mm	88014005	1.5"	16.5m3/hr	150
SMG750 - 30" - 770mm	88014063	2"	22.1m3/hr	250
SMG900 - 36" - 920mm	88014064	2"	32m3/hr	375