DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Boulder Tiled Pattern Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 48” and 52” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Doughboy, Vouge, Teakwood Discovery, Equinox , Regatta & Regatta II, Topaz, Reprieve, Oracle, Trevi 205, Summer Days.

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Cube Tiled Pattern Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 48” and 52” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Doughboy, Vouge, Teakwood Discovery, Equinox , Regatta & Regatta II, Topaz, Reprieve, Oracle, Trevi 205, Summer Days.

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Plain Blue Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 36” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Splasher

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

Replacement Plain Blue Overlap Liners by Swimline are 16 thou on the floor & walls, to ensure a professional installation only install the liner on a warm and dry day as these are stretched into place to prevent creases. These liners are suitable for 48” and 52” wall heights and due to the nature of this product these are non-returnable so please be sure you have measured your pool correctly before placing an order.

The Overlap liner is probably the least expensive liner you can buy on the market but if installed correctly can look as good as any other, please ensure all preparation works are carried out to manufactures guidelines as any imperfections will be shown once you start filling with water. Here are a few liner installation guidelines that we would strongly suggest following 

Liner Installation Instructions

Install day must be a warm sunny day to replace your liner with very little wind, the hotter it is the easier the installation will be.

Leave your new liner in a conservatory or in a very warm spot to get the boxed liner as warm as possible before unpacking. This will ensure flexibility in the liner when it comes to install day

Prepare your pool Base very carefully, sweeping the pool floor to remove all loose debris and sharp object which may push through. Always form a cove or install your Easy Cove at the bottom of the pool wall. The coving is a vital part in ensuring a lock is formed at the bottom of your pool. An inadequate cove will result in liner pushing underneath the wall causing the liner to fail.

Install your pool floor felt and foam walls if you have chosen that optional extra, the floor felt will protect your liner from abrasive damage from the floor of your pool, and give a soft feel underfoot. It will also soften any sudden impact with the pool floor.

When overlapping your liner be careful not to drag it over any sharp edges to puncture the liner and make sure the overlap is even all the way round. Once you have overlapped it so much aim to have the liner 3” to 6” off the ground before filling and clamp down with heavy duty pegs. 

Start filling the pool, at this stage there should be 1 person inside the pool trying to move out any excess liner material to the edges and ensuring they control the helpers outside the pool to release or hold the liner as necessary.

Whilst filling do not be tempted to drop to much liner in at once as creases will not be able to be pulled out due to the weight of the water. Drop liner in small and even quantities until water level has reached pools walls, at this stage you should not have to drop any more liner in.

These replacement overlap swimming pool Liners are suitable for all sizes of the following pools:
Doughboy, Vouge, Teakwood Discovery, Equinox , Regatta & Regatta II, Topaz, Reprieve, Oracle, Trevi 205, Summer Days.

These liners have a material thickness of:
Wall - 16 thou thick Virgin Vinyl and Floor - 16 thou thick Virgin Vinyl
This liner fitting is a 2 to 4 man job - please do not try this with 1 person.

Please note that all warranty claims on liners are only valid if any fault is found on a manufactured seam. All the liners are reverse inflated when manufactured to ensure water tightness, so no warranty can be accepted for holed liners.

DO NOT USE ANY KNIVES WHEN OPENING THE LINER PACKAGING.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Easy Cove for above ground swimming pools are ideal in forming a perfect smooth edge along the bottom edge of the pool, some engineers tend to use a sand or sifted soil cove which can cause problems in time.

The sand/soil can gradually be washed away leaving large gaps in between the pool wall and floor, in time the liner can be pushed through these gaps under pressure from the water and could eventually cause the liner to split. This can be prevented by using easy cove, which comes with an adhesive strip along the back to stick to the bottom of the pool wall; this will not wash away or rot away.

Easy Cove is a cheap but effective way to prevent these problems occurring

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Kingspan XPS thermal boarding (Styrozone H350r) will make a significant difference in your swimming pool heating costs. Whether it is because you are legally required as in the case of indoor swimming pools or not in the case of outdoor pools it make 100% sense to insulate your swimming pool. Energy costs are only going to get higher and although there are great heating systems now available it is important to retain the heat you are generating as much as possible. Our XPS Thermal Boards are great value compared to other systems available and are easy to install. These Thermal Boards will insulate your Pool Walls and Floor to a U-Value of .22. The legal requirement for indoor swimming pools is .25.

Part L building regulations - Conservation of fuel and power, require indoor swimming pools to be correctly insulated, if you would like to discuss the requirements in more detail please call us on 0132255870 and speak to one of our technical advisers. 

Please note that other types of insulation such as EPS, Jablite, Polystyrene will absorb water and will have a reverse effect. If you are looking to properly insulate your pool the XPS boards are a great value system designed for pool insulation.

Each XPS board is .75sqm and comes in 1250 x 600 x 80mm. Fitting these thermal boards to swimming pool such as our Kafko Pool is an easy add-on and will provide long term peace of mind in terms of energy saving and reduced running costs

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days.

RETURNS: All products can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Repair Kits For Swimming Pool Vinyl Liners. Clear Vinyl Strip & Vinyl Adhesive perfect for repairing inground and above ground liners swimming pools.

 How Do I Repair A Vinyl Liner?

Using our vinyl liner repair kit it is possible to patch a liner and make a repair either above or below the waterline. Each vinyl repair kit comes with a tube of solvent adhesive, an applicator and a length of strong, clear PVC that, when applied to the Swimming pool liner wall or floor will waterproof the liner and negate the need to replace it.

Can I Use The Vinyl Repair Kit Underwater?

Our Vinyl Liner Repair Kits are suitable for use above or underwater. If using the repair kit underwater cut the clear vinyl into an Oval or Circle, apply the adhesive on one side, then fold that side onto itself so the adhesive is not visible. To apply the patch underwater you must then take the patch to the split or hole in the liner and then open it up and immediately apply to the liner wall or floor. Firm pressure must be applied for at least 30 seconds to allow the weld to happen and this will give you a strong repair.

Will The Repair Patch Match My Liner?

The Vinyl Liner Repair Kit uses Clear Vinyl, so it is compatible with any liner. It also compatible with any liner pool, whether it is an inground pool or an above ground pool. If you have an above ground pool we recommend adding a patch on both the outside and inside if possible.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days.

RETURNS: All products can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Fix A Leek is the best swimming pool repair product available. If you are losing water in Your Swimming Pool but not sure where, Fix a Leak can prevent a frustrating, time consuming and expensive process which may require excavation to find a potentially small leak. Fix-A-Leak is one of the most trusted products available and is used by pool professionals in making permanent repairs without any significant costs FIX-A-LEAK is a blended concentrated liquid product that has been designed to seal leaks in virtually any material and is a favourite pool engineers products in resolving potentially expensive repairs. Fix a Leak is used to fix leaks in the shell and/or plumbing and will seal holes 1/8" in diameter. Once sealed the bond is permanent.

Fix a Leak is imported from the USA so the measurements on the bottle are based on quarts. To convert to litres x by 1.1326. 1 x 32oz bottle will treat 17,500 litres of water. Do not use in excess of 1 quart per 5,000 gallons of water.

DIRECTIONS
* Shake Well Before Using*
1. Bypass FILTER MEDIA before adding FIX-A-LEAK to water. Sand filters: Set multiport valve to recirculate.
2. With the filter pump running, add FIX-A-LEAK slowly through skimmer or in front of any other suction intake.
3. After adding FIX-A-LEAK adjust suction to the main drain. If this is not possible, the vacuum cleaner could be used alternatively, simply by placing the vacuum in deepest part of pool and connect to normal vacuum connection. Set filter valve to normal vacuum position.
4. FIX-A-LEAK is very heavy liquid and will sink to the lowest point rather quickly. It must be stirred back into suspension, either manually or by using a pool cleaner every 4-6 hrs. during circulation of water.
5. Continue to recirculate water until the leak has stopped.
6. To check if the Fix A Leak has found the leak and sealed you should mark the water level and check over the next few days to determine if the leak has stopped.
7. If you are happy that the water level is stable and the leak fixed you will need to wait 1 to 2 days in order to cure properly. After this time you can switch back to normal filtration.
Sand Filters: Set multiport valve to filter. Backwash out unused FIX-A-LEAK .
8. Suction Line Leaks - In most cases suction lines only leak water when the filter pump is shut off.

Normal Circulation will simply draw FIX-A-LEAK away from the leak and if the pump is shut off the material will simply not get to the leak. You must reverse the flow of water, to force the material through the leak under pressure. Preferably 5-10 psi. until the leak has stopped. When this has been achieved, gradually increase pressure to 15-25 psi. to insure a proper seal.

VERY IMPORTANT: After sealing a suction leak "it" is a must to leave suction off the repaired line for no less than 48 hrs. FIX-A-LEAK requires time to cure and harden.

Miscellaneous Leaks:
If you suspect a leak around fittings inside the pool (such as return fittings) lights, skimmer(s) or steps, etc. Shut down pump.
Apply FIX-A-LEAK directly to the leak using a squeeze bottle, similar to a ketchup bottle.
Allow a minimum of 48 hrs. to cure before starting up circulation.

DELIVERY: Swimming Pool Epoxy Repair Putty Stick is sent out on a next working day service but all standard deliveries will be within 5 working days.

RETURNS: Epoxy Repair Putty Stick can be returned if unopened and in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Epoxy Repair Putty Stick is a two part epoxy putty with a four year shelf life. This underwater repair putty is applied by simply breaking off what you need. Epoxy Repair Stick forms into a white finish.

Swimming Pool Epoxy Repair Putty Stick is a two-part epoxy putty with a four-year shelf life. To apply simply break off what you need. Knead then apply. Epoxy Repair Putty Stick forms into a white concrete. Epoxy Repair Putty Stick is easy to apply, the mix will be white and will harden within 20-30 minutes. In 24 hours, it will be rock hard.

Epoxy Repair Putty Stick can be used for a wide range of uses including underwater repairs, piping repairs, water tank and waterproofing. Epoxy Repair Putty is environmentally and ecologically friendly. Epoxy Repair Putty Stick will glue swimming pool tiles underwater, it can be used to repair concrete pool surface cracks and particularly handy with fibre-glass repairs and ABS

DELIVERY: Swimming Pool Ladders are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.

RETURNS: Swimming Pool Ladders can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.

PRODUCT INFO:

Standard Swimming Pool Ladder by Plastica in Hastings, UK and is made from 1.5" 304 Grade Stainless Steel Tube. You can choose between 2 and 5 White ABS Ladder Treads as standard.

306 grade ladders are available at an additional cost. 306 ladders are suitable for pools with salt system

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: Wooden Pool Ladders can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.

PRODUCT INFO:

The wooden pool ladder is a great looking inground pool style ladder that attaches to the top rail of your wooden swimming pool, each hand rail has a flange that takes 3 bolts to secure it safely to the wooden top rail. This ladder is suitable for any depth pool.

The Stainless Steel Wooden Pool Ladder can be a real focal point to a pool and the stainless steel makes this look great.The two hand rails has a flange that takes 3 bolts to secure it safely to the wooden top rail, and uses at actual sturure of the pool to support yout weight when entering the pool. This is done by having the feet of the ladder pointing towards the wall, so not only does this have more strength but it can now be used ur any depth size wooden pool

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Swimming Pool Ladder Accessories

 Simply click on the drop down box to view our range of ladder accessories and fittings. Treads, hinges, fittings and anchors are made to fit Plastica pool ladders.

DELIVERY: We aim to send Plastica Wooden Pools out on a next working day service but all standard deliveries will be within 10 working days as the wood may need to be tanalised

RETURNS: Plastica Wooden Pools are made to order and cannot be returned unless of a manufacturing defect.

PRODUCT INFO:

The 2023 Belgravia wooden pool, made in the UK by Plastica 5.6m x 3.7m internally stretched octagonal structure is perfect for all garden sizes. This pool is great for the more serious swimmer.

Plastica 3.7m x 5.6m Belgravia Wooden Pool comes with all the high-quality components that have made Plastica Wooden Pools the best value for money wooden pools in the UK.

These pools are easy to install yourself and are strong & durable, coming with a guaranteed 10 year warranty. 

For Our Full Range Of Wooden Pools CLICK HERE

Belgravia 5.6m x 3.7m Plastica Wooden Pool Dimensions & Specifications

Internal Dimensions : 5.564m x 3.695m
External Dimensions : 6.082m x 4.212m

• Redwood Walls & Structure
• New Upgraded Two piece hardwood top
• Hidden fixings kit
• 2 Braces
• Internal Stainless Steel ladder
• External Wooden ladder
• Felt and foam underlay
• Solar cover
• Installation guide and assembly dvd
• 10 year warranty on wall

Supplied with Plastica wooden pools are:

Robust 44mm pressure treated Redwood timber, selected from renewable sources. With all the necessary timber supports and fixings, as well as external and internal ladders. The two-piece reversible hardwood top shelving now uses a "plug & pellet" hidden fixing to ensure a simple, neat finish.

Metal braces, required for the Belgravia 5.6m x 3.7m Plastica Wooden Pools, now come with clever timber boxing panels, to keep the aesthetics of the timber flowing.

Foam underlay for the walls and felt underlay for the floor give the soft feel to the liner as well as adding protection.

Solar & Winter Covers can be designed for your specific pool.

Liner upgrades available as well as extras such as heaters, maintenance kits, LED lighting and extra piping.

DELIVERY: Bayswater Plastica Wooden Pools will be sent within 12 Weekss

RETURNS: Plastica Bayswater 3.6m x 5.5m Wooden Pool is classed as made to order and as such cannot be returned unless there is a manufacturing defect. If there is a manufacturer's defect it can be returned within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post. A Returns Number must be obtained before sending goods back.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors..

PRODUCT INFO:

The Plastica ‘’Bayswater’’ is the middle of 3 different Premium Wooden Pool Designs. Being 3.7m x 6.6m it was the middle size between the ‘’Belgravia’’ and ‘’Westminster’’ so it is the perfect choice if those models were either too big or small. This Wooden Swimming Pool will provide and create a load of family memories produced by hours of enjoyment and laughter.

3.7m x 6.6m ''Bayswater'' is the middle range of Wooden Pool, manufactured by Plastica Pools who are the largest suppliers in the UK. An easy to build DIY Wooden Pool that will look Fantastic in anyone’s back garden. Produced by Plastica Pools the 3.7m x 6.6m ‘’Bayswater’’ is the mid-range Wooden Pool but is big enough for all your family to enjoy and play in but still an average size to be heated without costing a small fortune.

Having a 3.6m x 6.6m size Wooden Pool will allow you to keep it warm all summer or even all year round without the worry of huge running costs. 

For Our Full Range Of Wooden Pools CLICK HERE

Plastica Bayswater 3.7m x 6.6m Wooden Pool Dimensions & Specification

Internal Dimensions : 6.564m x 3.694m
External Dimensions : 7.092m x 4.222m

• Redwood Walls & Structure
• New Upgraded Two piece hardwood top
• Hidden fixings kit
• Internal Stainless Steel ladder
• External Wooden ladder
• Felt and foam underlay
• Solar cover
• Installation guide and assembly dvd
• 10 year warranty on wall

''Bayswater' Wooden Pool provides a 4ft constant depth swimming pool which is more than deep enough to be able to swim lengths and to give you piece of mind if teenage kids were to be left alone in the Swimming Pool. A lot of people are scared off from buying a swimming pool because of the stories they hear from running costs on heating the pool, but technology has moved on so much that heating your Swimming Pool can be very cost effective if done correctly. You can purchase a low cost heat pump to heat your pool for short period of the summer when the pool will be in use and you even add a solar heating package to gain absolutely free heating source from the sun.

The most cost effective way of heating you pool would be a heat pump which will cost pennies rather than pounds per hour and you can even reduce that with a solar heating package, for advice on which is the best and most cost effective way of heating your pool would be please do not hesitate to contact us.

The 3.6m x 6.5m Wooden Swimming Pool by Plastica is designed to be DIY kit and ready for any comfortable DIY’er to build. And to be sure everything goes smoothly and correctly we offer free advice 7 days a week whenever needed.

Metal braces, required only on Stretched Octagon pools such as the Bayswater Wooden Pool, now come with clever timber boxing panels, to keep the aesthetics of the timber frame flowing.

Foam underlay for the walls and felt underlay for the floor give the soft feel to the liner as well as adding protection.

Solar & Winter Covers can be designed for your specific pool.

Liner upgrades available as well as extras such as heaters, maintenance kits, LED lighting and extra piping.

 If you would like to discuss which Plastica wooden pool would best suit your garden please call us on 01322 554 870

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

The Endless Pool Fastlane Counter Current Unit is renowned as being the most effective and pleasurable system available.

DELIVERY OF FASTLANE UNITS ORDERED IN JANUARY / FEBRUARY 2021 WILL BE JUNE / JULY 2021

Known for it's similarity in swimming in open water it is first choice for the serious swimmer, but is just as much fun for the kids, turning your pool into a waterpark.

Exercising with Endless Pools Fastlane is simple, with either the rero-fit option, turning your existing pool into a lap pool or the in-wall option for the new build.

52 discrete programmable speeds, all changeable via the water resistant wireless remote control, offer different swim levels up to a 66 Second 100 Yard pace (5HP).

Call us on 01322 554 870 to discuss the best option for your Endless Pools Fastlane Counter Current System.

DELIVERY: Plastica Wooden Pools are sent out via a specialist delivery company

RETURNS: This product is made to order and classed as a special order and cannot be returned unless there is a manufacturing defect.

PRODUCT INFO: 

Made by Plastica, this "Over The Wall" Wooden Exercise Pool offers something for the whole family. In addition to providing a place for serious exercise the Plastica X-Stream Wooden Exercise Swimming Pool offers fun for the whole family. Everyone in your family, including the youngest members with proper supervision, will enjoy playing and relaxing in your X-Stream Exercise Swimming Pool.

Swimming is considered to be the most beneficial form of exercise whilst building strength and stamina and reducing stress to the body joints due to the buoyancy of the water. If you have not got the room for a full size pool in your garden then why not install a Plastica X-Stream exercise swimming pool, 3.9m long x 2.4m wide x 1.17m high, fitted with a choice of four Over The Wall Counter Current Jet Systems.

Choose the Aquajet 100 swim Jet to create your own counter current swim, matching your swimming capabilities. For "hardcore" Triathletes we would recommend looking at the X-Stream Exercise Pool. It has a through the wall counter current system for a more "lifelike" Open Water swimming experience.

The Aquajet 100 has a flow rate up to 100m3 per hour

This easy to install pool has been carefully designed to suit all members of the family from the strongest of swimmers to beginners. The wooden exercise pool provides endless swimming and can be used for all types of swimming techniques, or as an air-bubble bath for under water massage.

This Plastica Wooden exercise pool can be installed either above the ground, requiring minimal ground work, or in-ground providing an easy installation and aesthetically pleasing addition to your home leisure and exercise routines.

For further information on installation, help and advice please call our customer service team on 01322 554 870

DELIVERY: Steel Swimming Pools are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.

RETURNS: Steel Swimming Pools can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.


When a return is received back into our warehouse our returns department confirm that everything is present and that the item is in its original condition, to make sure it is eligible for a refund. We will process the refund normally on the same day we take them in, but please allow up to a maximum of 14 working days for the money to reach your bank or credit card. It is unlikely to take this long but due to reasons such as bank delays or errors, this may occasionally occur.

PRODUCT INFO:

15ft Round Steel Walled Swimming Pool with 42" Wall Height Making It Ideal For A Family With A Young Family. Affordable & Fitted With Same Filtration Equipment Included In Our Doughboy Pool Packages

The 15ft Round 42 Inch deep Steel walled pool package is the perfect permanent pool to start off with as the 42" wall depth gives you a 3ft (36") water depth which is more suitable for younger families.

When your young children grow up and can safely stand in deeper pools, then you can simply take this 15ft Round 42" Steel Wall Pool down, sell it on or give it to a friend and install a deeper pool.

DELIVERY: Steel Swimming Pools are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.

RETURNS: Steel Swimming Pools can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.

When a return is received back into our warehouse our returns department confirm that everything is present and that the item is in its original condition, to make sure it is eligible for a refund. We will process the refund normally on the same day we take them in, but please allow up to a maximum of 14 working days for the money to reach your bank or credit card. It is unlikely to take this long but due to reasons such as bank delays or errors, this may occasionally occur.

PRODUCT INFO:

12ft Round Steel Walled Swimming Pool with 42" Wall Height Making It Ideal For A Family With A Young Family. Affordable & Fitted With Same Filtration Equipment Included In Our Doughboy Pool Packages

The 12ft Round 42 Inch deep Steel walled pool package is the perfect permanent pool to start off with as the 42" wall depth gives you a 3ft (36") water depth which is more suitable for younger families.

When your young children grow up and can safely stand in deeper pools, then you can simply take this 12ft Round 42" Steel Wall Pool down, sell it on or give it to a friend and install a deeper pool.

DELIVERY: Steel Swimming Pools are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

18ft x 12ft Oval Steel Walled Swimming Pool with 42" Wall Height Making It Ideal For A Family With A Young Family. Affordable & Fitted With Same Filtration Equipment Included In Our Doughboy Pool Packages

The 18ft x 12ft Oval 42 Inch deep Steel walled pool package is the perfect permanent pool to start off with as the 42" wall depth gives you a 3ft (36") water depth which is more suitable for younger families.

When your young children grow up and can safely stand in deeper pools, then you can simply take this 18ft x 12ft Oval 42" Steel Wall Pool down, sell it on or give it to a friend and install a deeper pool.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

24ft x 12ft Oval Steel Walled Swimming Pool with 42" Wall Height Making It Ideal For A Family With A Young Family. Affordable & Fitted With Same Filtration Equipment Included In Our Doughboy Pool Packages

The 24ft x 12ft Oval 42 Inch deep Steel walled pool package is the perfect permanant pool to start off with as the 42" wall depth gives you a 3ft (36") water depth which is more suitable for younger families.

When your young children grow up and can safely stand in deeper pools, then you can simply take this 24ft x 12ft Oval 42" Steel Wall Pool down, sell it on or give it to a friend and install a deeper pool.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Replacement Doughboy Liners for both the Regent and Premier. High quality liners with unbeatable warranty on the seam. In stock for quick delivery

Doughboy Replacement Liners are all plain blue overlapping liners which are stretched into place, this can be a difficult task to do so please follow the instructions below.

1. Check and Double Check: It’s is vital to check that all levels and measurements are correct before positioning your Doughboy Liner. The cove is a vital structural element that prevents water pressure from forcing the liner out under the bottom rail. So please be sure that cove is installed correctly by manufactures guidelines.
2. Seam Positioning: Check the pool floor (area inside the walls) for levelness. Fill in all depressions and remove any stones or sharp object from floor. Place the Doughboy liner on the top of top rail, the liner should have overhanging the outside wall by 12” inches. Hold end and unroll liner down middle of pool as you would carpet, do not place liner seam over skimmer or return fitting openings.
3. Install Liner: Work in both directions from the point where is already overhanging, unfold Doughboy liner, drape over the top rail and down the sides approximately 24” inches. The liner should be barely above the pool floor in the centre only. Remember that the centre seam or centre of the Doughboy Plain Blue liner should be inside the pool about 12” inches below the top rail. Correct any bunching or pleating conditions in the liner wall. Inspect the liner for open seams if any found return to dealer for prompt replacement of liner.
4. Fill Pool: With the Doughboy Plain Blue liner in position, hold in place by attaching heavy duty clips over folded cardboard on the underside of each top rail. Carefully cover the end of the garden hose with a sock and tape securely, once this is done place hose inside the pool and start filling. As pool fills the liner will stretch as the water begins to cover the bottom. At this point check the walls for EXTREME tautness, release clips if need be but be sure not to release too much slack as this will cause creases. When releasing the clips you will also need to keep in mind the clips will need to be loosened evenly for whole circumference of the pool (Doughboy advise very little amounts at a time). Once the water reaches past the cove the tension should ease off dramatically and you should have no wrinkles on the floor. Creases in the wall can be removed by re-tauting the Doughboy Plain Blue liner over the wall,
5. Procedure to attached liner: With the help of two or three people, raise and hold the Doughboy Plain Blue liner up from any three top rail sections. Remove some of the top rail completely and stretch the Doughboy liner over metal wall as tight as possible, then re-erect the top rail with the liner in position and repeat the procedure all the way round the pool (Remembering only taking 2-3 sections off at one time) Once this is completed and the water is at correct level then the water can be turned off and cuts to the liner can be made.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Replacement Doughboy Liners for both the Regent and Premier. High quality liners with unbeatable warranty on the seam. In stock for quick delivery

These Doughboy Replacement Liners are all patterned overlap liners which are stretched into place, this can be a difficult task to do so please follow the instructions below.

1. Check and Double Check: It’s is vital to check that all levels and measurements are correct before positioning your Doughboy Liner. The cove is a vital structural element that prevents water pressure from forcing the liner out under the bottom rail. So please be sure that cove is installed correctly by manufactures guidelines.
2. Seam Positioning: Check the pool floor (area inside the walls) for levelness. Fill in all depressions and remove any stones or sharp object from floor. Place the Doughboy liner on the top of top rail, the liner should have overhanging the outside wall by 12” inches. Hold end and unroll liner down middle of pool as you would carpet, do not place liner seam over skimmer or return fitting openings.
3. Install Liner: Work in both directions from the point where is already overhanging, unfold Doughboy liner, drape over the top rail and down the sides approximately 24” inches. The liner should be barely above the pool floor in the centre only. Remember that the centre seam or centre of the Doughboy Patterned liner should be inside the pool about 12” inches below the top rail. Correct any bunching or pleating conditions in the liner wall. Inspect the liner for open seams if any found return to dealer for prompt replacement of liner.
4. Fill Pool: With the Doughboy Patterned liner in position, hold in place by attaching heavy duty clips over folded cardboard on the underside of each top rail. Carefully cover the end of the garden hose with a sock and tape securely, once this is done place hose inside the pool and start filling. As pool fills the liner will stretch as the water begins to cover the bottom. At this point check the walls for EXTREME tautness, release clips if need be but be sure not to release too much slack as this will cause creases. When releasing the clips you will also need to keep in mind the clips will need to be loosened evenly for whole circumference of the pool (Doughboy advise very little amounts at a time). Once the water reaches past the cove the tension should ease off dramatically and you should have no wrinkles on the floor. Creases in the wall can be removed by re-tauting the Doughboy Patterned liner over the wall,
5. Procedure to attached liner: With the help of two or three people, raise and hold the Doughboy Patterned liner up from any three top rail sections. Remove some of the top rail completely and stretch the Doughboy liner over metal wall as tight as possible, then re-erect the top rail with the liner in position and repeat the procedure all the way round the pool (Remembering only taking 2-3 sections off at one time) Once this is completed and the water is at correct level then the water can be turned off and cuts to the liner can be made.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

End Caps for Easy Drain Plus Swimming Pool Drainage Channel

Easy Drain Plus is an easy, but effective way of draining excess water from around your swimming pool, spa or shower area. Easy to install and designed to fit 1.5" swimming pool pipe

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

4 Way Cross Piece For Easy Drain Plus

Easy drain plus is a rigid PVC drainage system ideal for use on your indoor pool, the drainage channels will get rid of that unwanted water that sits around your pool caused by splashing. 

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

135 Degree Angle For Easy Drain Plus

Easy drain plus is a rigid PVC drainage system ideal for use on your indoor pool, the drainage channels will get rid of that unwanted water that sittings around your pool caused by splashing. Available in 3m lengths and a range of different fittings to suit every pool.

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

Easy Drain Plus 1.5" Downspout Pipe to connect to 1.5" swimming pool pipe.

Easy drain plus is a rigid PVC drainage system ideal for use on your indoor pool, the drainage channels will get rid of that unwanted water that sits around your pool caused by splashing. 

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

50mm Downspout Piece For Easy Drain Plus will let you connect Easy Drain Plus to 50mm plumbing pipe easily and quickly.

Easy drain plus is a rigid PVC drainage system ideal for use on your indoor pool, the drainage channels will get rid of that unwanted water that sits around your pool caused by splashing. 

DELIVERY: We aim to send all products out on a next working day service but all standard deliveries will be within 5 working days

RETURNS: This product can be returned in original packaging, suitable for resale, within 14 days from date of delivery.

PRODUCT INFO:

DELIVERY: We aim to send Coping Stones within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

9" Swimming Pool Coping Stones in Buff or White. These are hand finished coping stones, flat topped.

We have selected standard size swimming pools for coping stone prices but can supply smaller quantities or bespoke requests if required

DELIVERY: We aim to send Bullnosed Coping Stones within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

9" Bullnosed Swimming Pool Coping Stones from World of Pools in Buff or White. These are hand finished coping stones 200mm x 600mm x 40mm .

We have selected standard size swimming pools for these 9" Bullnosed Coping stone prices but can supply smaller quantities or bespoke requests if required

DELIVERY: We aim to send Bullnosed Coping Stone Kits within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

9" Bullnosed Swimming Pool Coping Stones from World of Pools in Buff or White. These are hand finished coping stones 200mm x 600mm x 40mm .

We have selected standard size swimming pools including standard 4' x 6' Roman end for these 9" Bullnosed Coping stone prices but can supply smaller quantities or bespoke requests if required

DELIVERY: We aim to send 12" Bullnosed Coping Stones within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

12" Bullnosed Swimming Pool Coping Stones from World of Pools in Buff or White. These are hand finished coping stones 200mm x 600mm x 40mm .

We have selected standard size swimming pools for these 12" Bullnosed Coping stone prices but can supply smaller quantities or bespoke requests if required

DELIVERY: We aim to send Bullnosed Coping Stone Kits within 5 working days

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

PRODUCT INFO:

12" Bullnosed Swimming Pool Coping Stones from World of Pools in Buff or White. These are hand finished coping stones 305mm x 600mm x 40mm .

We have selected standard size swimming pools including standard 4' x 6' Roman end for these 12" Bullnosed Coping stone prices but can supply smaller quantities or bespoke requests if required

DELIVERY: Mega Pool Building Bricks are delivered within 2 weeks, given the size and delivery logistics for this size of Pool we will work with customer in creating best possible delivery time

RETURNS: This product is produced to order and as such is classed as a special order and cannot be returned unless there is a manufacturers defect

If there is a manufacturers defect his product can be returned in its original packaging, within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post. A Returns Number must be obtained before sending goods back.

.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors.

PRODUCT INFO:

Mega Pool Building Bricks are similar to Blokit, but have an additional 10mm layer of Insulation giving a maximum Heat Transfer U Coefficient Is 0.414Wm2/K.

Building your swimming pool with the Mega Pool Building Brick will allow you to quickly complete the project with the least amount of overdig, reducing costs, time and the impact on your garden.

The Build is quick and efficient, with the hollow blocks allowing for Re-Bar reinforcing steel to be added, then the concrete poured. And to help reduce costs even more each 1m2 section of wall only requires 0.133m3 of concrete.

Once the pool walls are built we would recommend finishing the pool with an On-Site Liner, offering ease, strength, longevity and beauty in one simple Waterproofing process.

If you would like to discuss or find out more about the Mega Pool Build Brick please call us on 01322 554 870

Each Layer of Mega Pool Building Bricks requires 8 End Pieces

Number Of Blocks Required For Pools With A 1.25m Wall Height

DELIVERY: Plastica Wooden Pools will be sent within 10 working days

RETURNS: The Plastica Westminster 8.2m x 4.6m Wooden Pool is classed as made to order and as such cannot be returned unless there is a manufacturing defect. If there is a manufacturer's defect it can be returned within 14 days from date of delivery. Returns should be sent via a "Signed For" carrier or post. A Returns Number must be obtained before sending goods back.

.

When we receive the item, our returns department confirm that everything is present and in its in original condition to ensure its eligibility for refund. We process refunds as quickly as possible. We process most refunds on the same day which they were received, but please allow up to a maximum of 14 days for the money to reach your account. It rarely takes this long, but can happen sometimes for reasons such as bank delays or errors.

PRODUCT INFO:

The Plastica ‘’Westminster’’ is the largest Premium Stretched Octagonal Wooden Pool Plastica manufacture. Being 8.2m x 4.6m it was the biggest wooden pool, other than the rectangular Chelsea, which is 10m x 5m. The Westminster Wooden Swimming Pool will help create so many happy family memories produced by hours of enjoyment and laughter in your own personal super-sized swimming pool.

8.2m x 4.6m Westminster wooden pool will hold 39,200 Litres (8,600 UK Gallons) of water, so you will need to think how to heat the pool before you buy it. Calling us on 01322 554 870 to discuss the best options will make the whole process of buying and building the pool so much easier. All Plastica Wooden Pools are an easy to build DIY Wooden Pool that will look Fantastic in anyone’s back garden. Produced by Plastica Pools, in the UK, the 8.2m x 4.6m Westminster Wooden Pool is big enough for all your family to enjoy and play in but still a size that can be heated without costing a small fortune.

Having an 8.2m x 4.6m sized Wooden Pool with one of our heat pumps, sized for this poo, will allow you to keep it warm all summer or even all year round without the worry of huge running costs normally associated with Oil or Standard electric heating. 

For Our Full Range Of Wooden Pools CLICK HERE

Plastica Westminster 8.2m x 4.6m Wooden Pool Dimensions & Specification

Internal Dimensions : 8.191m x 4.611m
External Dimensions : 8.719m x 5.139m

• Redwood Walls & Structure
• New Upgraded Two piece hardwood top
• Hidden fixings kit
• Internal Stainless Steel ladder
• External Wooden ladder
• Felt and foam underlay
• Solar cover
• Installation guide and assembly dvd
• 10 year warranty on wall

The Plastica Westminster Wooden Pool has a wall height of 1.35m, which provides a 4ft constant water depth swimming pool, more than deep enough to be able to swim lengths whilst giving you peace of mind that teenage kids will not be out of there depth, if they were to be left alone in the Swimming Pool.

Heating a pool this size is essential in the UK, if you are going to see any use from it. Our experience, from being one of the first online Swimming Pool companies in the UK, has provided us with a wealth of knowledge that will allow us to size a heating package designed perfectly for your needs and budget. You can purchase a low-cost heat pump to heat your pool for the summer, with the addition of solar to reduce the running costs. If required a heat pump can be supplied that will work all year round, but on this size pool that is not the norm.

Call Us On 01322 554 870 for the best advice on how to heat this pool cost effectively

The 8.2m x 4.6m Westminster Wooden Swimming Pool by Plastica is designed to be DIY kit and ready for any comfortable DIY’er to build. And to be sure everything goes smoothly and correctly we offer free advice 7 days a week whenever needed.

Metal braces, required only on Stretched Octagon pools such as the Westminster Wooden Pool, now come with clever timber boxing panels, to keep the aesthetics of the timber frame flowing.

Foam underlay for the walls and felt underlay for the floor give the soft feel to the liner as well as adding protection.

Solar Cover Upgrades & Winter Covers can be designed for your specific pool.

Liner upgrades available as well as extras such as heaters, maintenance kits, LED lighting and extra piping.

 If you would like to discuss which Plastica wooden pool would best suit your garden please call us on 01322 554 870

DELIVERY: We aim to send Plastica Wooden Pools out with -in three months but all standard deliveries will be within 6 weeks working days as the wood may need to be tanalised

RETURNS: Plastica Wooden Pools are made to order and cannot be returned unless of a manufacturing defect.

PRODUCT INFO:

The Chelsea 10m x 5m wooden pool, made in the UK by Plastica, is the only fully rectangular wooden pool manufactured in the UK. The 10m x 5m rectangular wooden pool structure is perfect for large gardens and families. Larger than most inground pools, the Chelsea Wooden Pool will need to have an adequate heating supply, most likely a large heat pump sized for the pool and your swimming season requirements. It is best to call us on 01322 554 870 to talk to us about this before buying the pool. Being such a large pool this 10m x 5m Wooden Pool is great for the more serious swimmer.

With a few new additions and extra options for 2019 the Plastica 10m x 5m Chelsea Wooden Pool still comes with all the high-quality components that have made Plastica Wooden Pools the best value for money wooden pools in the UK, it is just much bigger than any other wooden pools

Although they are large the Chelsea Wooden Pool is still easy to install yourself and it is very strong & durable, coming with a guaranteed 10-year warranty on the wooden structure. 

For Our Full Range Of Wooden Pools CLICK HERE

Chelsea 10m x 5m Plastica Wooden Pool Dimensions & Specifications

Internal Dimensions:  10m x 5m
External Dimensions: 10.88m x 5.88m

• Redwood Walls & Structure
• New Upgraded Two piece hardwood top
• Hidden fixings kit
• 2 Braces
• Internal Stainless Steel ladder
• External Wooden ladder
• Felt and foam underlay
• Solar cover
• Installation guide and assembly dvd
• 10 year warranty on wooden walls & top rail

Supplied with Plastica wooden pools are:

Robust 44mm pressure treated Redwood timber, selected from renewable sources. With all the necessary timber supports and fixings, as well as external and internal ladders. The two-piece reversible hardwood top shelving now uses a "plug & pellet" hidden fixing to ensure a simple, neat finish.

Metal braces, required for the Chelsea 10m x 5m Plastica Wooden Pools, now come with clever timber boxing panels, to keep the aesthetics of the timber flowing.

Foam underlay for the walls and felt underlay for the floor give the soft feel to the liner as well as adding protection.

Solar & Winter Covers can be designed for your specific pool.

Liner upgrades available as well as extras such as heaters, maintenance kits, LED lighting and extra piping.