Nano Action 2.8kw Heat Pump For Above Ground Pools
- Nano Heat Pump Works At 10°C Air Temp
- in stock for fast delivery
- Plug & Play 3kw Heat Pump For Intex & Above Ground Pools
- Heats A 12m3 Pool To 30°C - Works Down To 10°C Air Temperature
- Only 8p Per Hour To Run
- 2 Year Parts Warranty
DELIVERY: Poolex Nano Plug & Play Above Ground Pool Heat Pumps & Hot Tub Heat Pumps are sent out via a specialist carrier. Delivery will normally take between 1-3 days, but please allow 5 working days in some extreme cases.
RETURNS: Poolex Nano Plug & Play Above Ground Pool Heat Pumps & Hot Tub Heat Pumps can be returned to us, in compliance with the Consumer Contracts Regulations, unused and in their original packaging, suitable for resale, within 14 days from date of delivery. Returns should always be sent via "Signed For" carrier or postal service.
Our returns address is Giraffe Enterprises Ltd, Bexley Garden Centre, 57 North Cray Road, Sidcup, Kent. DA14 5EU. Tel: 01322 554 870
When a return is received back into our warehouse our returns department confirms that everything is present and that the item is in its original condition, to make sure it is eligible for a refund. We will process the refund normally on the same day we take them in, but please allow up to a maximum of 14 working days for the money to reach your bank or credit card. It is unlikely to take this long but due to reasons such as bank delays or errors, this may occasionally occur
Poolex Nano Plug & Play Heat Pumps are ideal for above ground pools up to 12m3, such as an Intex or Bestway 12ft x 48" Metal Frame Pool.
It is suitable for heating a pool of 12m3 during the main Summer months. A Solar Cover has to be used whenever the pool is not in use, especially at night as this will speed up pool heating time and reduce heat loss at night by up to 5°C. Buy Now For Same Day Despatch.
The Nano Plug & Play Heat Pump requires 0.7kw of power to produce nearly 3kw of power out. That is roughly 8p an hour to get the equivalent of 40p of heat from the Poolex Nano Heat Pump into your pool making it so much cheaper to run than an electric pool heater. You could even recoup the outlay in the first year in savings on your electricity bill.
The minimum flow rate from your pool pump is 2m3/hr to start the Nano Plug & Play Heat Pump For Above Ground Pools. Most Intex & Bestway pumps exceed this but check before buying
Digital Heating Control Panel - Control Heating Up To 30°C
No ByPass Required if using small Intex pumps
The Poolex Nano Heat Pumps are designed to heat Pool water slowly but very cost-effectively. It can raise your pool from cold to warm in 2 - 3 days, but from then on it is just a matter of keeping the heat level topped up every day. Depending on the weather you may need to run your heat pump from between 4 - 10 hours a day.
A Good Quality Solar Cover Must be Used With This Heat Pump to preserve as much heat as possible, especially at night.
The Nano Plug & Play Above Ground Pool Heat Pump is suitable for pools up to 12m3
Below are suggestions for above ground pool sizes that the Nano Plug & Play Above Ground Pool Heat Pump is suitable for
|Bestway & Intex Metal Frame Pool Heat Pump|
|10ft x 30 inch Metal Frame Pool|
|12ft x 36 inch Metal Frame Pool|
|12ft x 48 inch Metal Frame Pool|
|Intex & Bestway Easy Set Pool Heat Pump|
|8ft x 30 inch Easy Set Pool|
|10ft x 30 inch Easy Set Pool|
|12ft x 30 inch easy Set Pool|
|12ft x 36 inch Easy Set Pool|
|15ft x 36 inch Easy Set Pool|
|15ft x 48 inch Easy Set Pool|